Sunday, July 31, 2011

A Claro Walnut/Sitka Spruce 000 - Free to Good Home!

I've made great advances with the last two guitars I've completed in terms of build quality and tone and I'm afraid I'm a little lacking in motivation when it comes to completing this one. I guess that's a little strange given my usual passion for guitar building, but considering that I began its construction quite some time ago and would much rather be working on my new instruments, putting into practice important lessons recently learned, I'm inclined to forgive myself for this half-hearted attitude.


The photograph above doesn't do the claro walnut back and sides justice; in its present raw state, the wood looks pretty uninspiring. Under finish, however, its stunning figure will be fully revealed and will be the icing on what I hope will be a very successful cake!

Tapping on this unusually marked Sitka spruce soundboard in its unfinished state gives me reason to be confident. The body is very resonant, the standard of workmanship is acceptable and construction is far enough advanced that I'm sure I can muster the enthusiasm to finish it. This guitar's state of completion will fall into line with my two latest instruments when they are ready to receive bindings. From that point on I'll attempt to complete the remaining steps on all three guitars concurrently.

Click for a closer look.

For what will hopefully be the last time, I plan on finding an appreciative recipient and making a gift of one of my instruments. It's certainly been very satisfying to have delivered my last two guitars to keen players free of charge, but once this guitar finds a new home, foregoing that pleasure and at last deriving some meagre income from my hobby is a prospect that's becoming increasingly attractive.  Semi-retirement (and a new band-saw) beckons!

Cheers
Pete

Sunday, July 10, 2011

The Fingerstyle Guitar - Head Block, Tail Block and Linings

Having braced the top, it's time to temporarily suspend my excitement and spend some time on the rims. For me, this is perhaps the least inspiring stage of construction and the reason I find it preferable to have a ready-made stock of head blocks, tail blocks and kerfed lining strips which I've prepared in batches over the preceding months.  With a supply of blocks and linings on hand, I can make short work of fitting them to the guitar's sides and move on quickly to more interesting tasks.

I laminate my tail blocks using three layers of wood, the middle layer of which has its grain oriented at right angles to the two outer layers, parallel with the grain of the sides. For the little additional effort involved, I can feel confident that the block will remain intact and a side crack will be avoided should the guitar ever be dropped on its end pin.

In the belief that setting modest targets fuels motivation and sustains momentum, I'm setting myself the goal of attaching the head and tail blocks and installing the kerfed linings in the week ahead.

Cheers
Pete

Friday, July 1, 2011

The Fingerstyle Guitar - Soundboard Voicing

Like many novice guitar builders I was inclined to overbuild my early guitars, the mortal fear of them imploding tending to override any suspicion that I was robbing them of their full tonal potential. It's been difficult to leave that mindset behind me, but with a conscious effort to "lighten up", and with the wisdom of more experienced luthiers in mind, I'm venturing further from my previous comfort zone with each guitar in an effort to increase their responsiveness. To that end, I've significantly reduced the mass of my soundboard braces, ever mindful of the delicate balance necessary between lightness and strength. Ironically, it's because of advice from those same sources that I'm inclined to leave the soundboard itself a little thicker than I may once have done.


John Mayes' "Advanced Voicing" DVD provided me with a way forward where carving the soundboard braces is concerned. Without a doubt, watching John shave and shape the soundboard braces then tap on the top to assess the changes he'd brought about has given me a much better insight into the process than I'd been able to gain through simply reading about other luthiers' methods in that regard. As John clearly demonstrates, judicious removal of small amounts of mass from one or more braces can make a big difference to the responsiveness of the soundboard.  It's still a somewhat mysterious and inexact science for me, but recent results suggest that I'm heading in the right direction at last.

There's some carving of brace ends and final finish sanding remaining, but essentially, the redwood top is as resonant as I can confidently make it without sacrificing necessary strength. Its pitch when tapped is significantly different to that of the Sitka spruce top I've recently brought to this level of completion and it will be interesting to compare the two guitars when they're strung up. For my own future reference, I intend to document each top's overall weight and brace dimensions as well as record their tap tones with a hand-held Zoom recorder, the thinking being that over time, as I complete more instruments, I'll be able to correlate these measurements with their sound when played.

Cheers
Pete

Postscript:  Since publishing this post yesterday, I've capped the "X" brace intersection with a small piece of spruce and the relative pitches of the two tops when tapped are now much closer.  It explains the startling difference I noticed yesterday and is a great demonstration of how this small addition can significantly increase the overall stiffness of the top.

What's In a Name?

The back and sides of this guitar are of narra, which is an alternative name for a wood that's most often marketed here in Australia as ...